glutathione is good for skin whitening Brightener™ Cream 100 ml R Vitamin
100 ml R Vitamin B1, B6, B12 Injection Bion 12 Plus at ₹ 260/piece in Vadakkanandal
Enriched with GHK-Cu and a unique combination of peptides, this lightweight serum helps reduce the appearance of fine lines, boosts collagen production, and restores skin elasticity
Face & Body Care Main
Packaging:40ml
Required: Your tirzepatide powder vial Bacteriostatic water (BAC water) -- this contains a preservative that keeps the solution safe for multiple uses over 28 days A sterile syringe, 3mL or larger, with needle Alcohol swabs A clean, flat, well-lit workspace Clean hands (wash thoroughly with soap) Strongly recommended: A calculator or your phone's calculator app A permanent marker for labeling A notebook to log reconstitution date and concentration Reconstitution Calculations Understanding Concentrations For a 30mg Tirzepatide Vial: For a 60mg Tirzepatide Vial: Choosing Your Concentration Higher concentration (10mg/mL): Smaller injection volumes Fewer injections per vial Good for higher doses Lower concentration (5mg/mL): Easier dose measurement Better for lower doses More precise titration Step-by-Step Reconstitution Preparation Phase Step 1: Gather Materials All supplies within reach Clean workspace Good lighting Hands washed thoroughly Step 2: Inspect Vials Check expiration dates Verify powder appearance (white/off-white) Ensure BAC water is clear No damage to seals Step 3: Calculate Your Volume Determine desired concentration Calculate BAC water needed Double-check math Write it down Mixing Phase Step 4: Clean Vial Tops Wipe both vials with alcohol Let dry completely (30 seconds) Don't touch cleaned surfaces Step 5: Draw Bacteriostatic Water Remove syringe cap Insert needle into BAC water vial Invert vial Draw calculated amount Remove air bubbles Step 6: Add to Tirzepatide Vial Insert needle through center of stopper Aim at side of vial (not directly on powder) Inject slowly Let water run down side Step 7: Mix Gently Do NOT shake vigorously Gently swirl in circular motion Roll vial between palms Continue until fully dissolved Step 8: Inspect Solution Should be clear No visible particles No cloudiness Slight yellow tint acceptable Post-Reconstitution Step 9: Label the Vial Write on vial: Reconstitution date Concentration (mg/mL) Expiration (28-30 days) Your initials Step 10: Store Properly Refrigerate immediately 36-46°F (2-8°C) Protect from light Keep upright Dosing from Reconstituted Vial Dose Calculation Formula Volume to inject = Desired dose (mg) ÷ Concentration (mg/mL) Example Calculations At 10mg/mL concentration: At 5mg/mL concentration: Storage After Reconstitution Refrigerated Storage Temperature: 36-46°F (2-8°C) Duration: 28-30 days maximum Keep in original vial Protect from light What to Avoid ❌ Freezing (destroys medication) ❌ Room temperature storage ❌ Direct sunlight ❌ Excessive handling Troubleshooting Powder Won't Dissolve Possible causes: Water too cold Not enough mixing time Damaged product Solutions: Let BAC water reach room temp Continue gentle swirling (up to 30 min) If still undissolved, contact pharmacy Solution Is Cloudy Possible causes: Contamination Degradation Improper storage Action: Do not use Discard safely Contact pharmacy for replacement Particles Visible What to do: Gently swirl again If particles persist, do not use Some settling may be normal When in doubt, replace Best Practices Do's ✅ Work in clean environment ✅ Double-check calculations ✅ Use fresh needle each time ✅ Store properly after each use ✅ Keep reconstitution log ✅ Follow expiration dates Don'ts ❌ Shake vigorously ❌ Use if cloudy or particulate ❌ Store at room temperature ❌ Reuse needles ❌ Use past expiration ❌ Expose to heat/light Before Every Injection: A Quick Checklist Each time you draw from the vial, take 30 seconds to verify: Is the solution clear
